PolyU provides support to the nation's landing on the far side of the Moon
"PolyU is very honoured to be involved in and to make contributions to the nation's lunar missions, in particular in this debut landing on the far side of the Moon, the first-ever in the history of mankind," said Professor Alex WAI, Vice President (Research Development)
Landing site characterisation
For the first lunar mission in the world to land a space craft on the far side of the Moon, the selection of a safe landing site with scientific value is of paramount importance. Dr Bo WU, Associate Professor of Poly's Department of Land Surveying and Geo-Informatics, has led a team to conduct a research titled "Chang'e-4 Landing Site - Topographic and Geomorphological Characterisation and Analysis" since March 2016.
Funded by the China Academy of Space Technology (CAST), the team amassed a large amount of lunar remote sensing data from multi-sources to create high-precision and high-resolution topographic models for two potential landing regions, one of them is the current Chang'e-4 landing site, the Von Kármán crater inside the South Pole - Aitken basin on the far side of the Moon.
Dr Wu and his team studied two landing regions for Chang'e-4 mission, each covering an area of about 1,500 square kilometers, which is 1.4 times of the total area of Hong Kong. They analysed in detail the terrain slopes, terrain occlusions to sun illumination and telecommunication, crater distribution, rock abundance, and geological history of the region. These analyses helped the team to put forward a sound and evidenced-based proposal of possible landing sites.
The team gathered information of more than 400,000 craters and over 20,000 boulders in the candidate landing regions. It had also analysed the terrain surface and calculated the gradient of the slopes to identify relatively flat sites for safe landing. Rock abundance of the region had to be considered in detail because boulders can be as large as 35 metres in diameter and can block the way of the rover, whereas small rocks may get into the wheels, hence creating problem in the rover's movement.
"The Chang'e-4 landing site is on the far side of the Moon, without direct radio communication from Earth," said Dr Wu. "In addition, the terrain surface of the landing region is also very rough with elevation differences up to 16km, which required a nearly perpendicular descent design. These made the mission very challenging."
The study in terrain occlusions to sun illumination and telecommunication is particularly important to ensure good illumination conditions to charge the solar panels on the lander and rover so that the onboard scientific sensors can be functional, and ensure good signal reception and data transmition between the control center on Earth and the lander and rover.
After the successful landing of Chang'e-4 on 3 January 2019, the team worked together with the CAST team to immediately locate the precise location of the lander and analysed the terrain occlusions to sun illumination and telecommunication around the lander for better scheduling of action of the lander and rover.
Dr Wu is excited to get involved in the project. "When I started my career in surveying, I have never dreamed of taking part in space exploration missions. But all things are possible if we are bold in taking out that one step," he shared.
Camera Pointing System
Prof. Kai-leung YUNG, PolyU's Chair Professor (Precision Engineering)
The CPS weighs 2.8 kg and measures 85 cm (length) by 27 cm (width) and 16 cm (depth). Mounted on the upper part of the lander of Chang'e-4, CPS is capable of moving vertically by 120 degrees and rotating sideway by 350 degrees, under Moon's gravity (i.e. one sixth of Earth's gravity). It is deployed for capturing images of the Moon as well as facilitating movement of the lunar rover.
The design of the sophisticated CPS is extremely complicated. To withstand the stringent environment and to ensure the proper functioning of the device once landed on the Moon, all electrical parts, signal lines and wirings are installed inside the product shell. A well-designed, complicated, precise interior structure has to be machined to install and protect all wirings properly. Good multi-axis machining know-how and experience is a must to complete this project.
The far side of the Moon receives high density of radiation and is exposed to extreme temperatures. The CPS therefore needs to be protected by the product shell with good surface finish and treatment to reflect the radiation and heat. And to avoid corrosion and rusting, the number of assembly parts and joints have to be minimised. As a result, many parts were specially combined to form one single component in the design stage and were machined and fabricated by removing unnecessary materials from one single solid material block. The process is far more complicated and time-consuming and needs high precision machining process design and know-how.
Ms Michelle Li,
Communications and Public Affairs Office, PolyU