Sample (life Cycle Assessment)

If you are about to appear for some competitive exams and need to be sure about scoring well, you could do with some online exam help. We can help you with preparing well for various online exams. You will get a lot of
By: www.sampleassignment.com
 
MELBOURNE, Australia - June 14, 2014 - PRLog -- LIFE CYCLE ASSESSMENT

EXECUTIVE SUMMARY

In the stage of design, the information is short along with the data and hence, there are various assumptions that have to be made. These assumptions

A mechanical duplexer is present in a canon printer and hence, whenever a double side printing is to be done, the printer would on its own consider the page change. The types of cartridges accepted by the printer are one for text and other for pictures.
one that is made by mixing the elements with brominated flame. The FR4 is measured in terms of copper. According to the known sources, it is estimated that the water used in making the boards of these printers alone is around  6 to 7 liters.

In asr connections consist of copper mainly. The coils on the circuit board have a little additional amount of copper Payne( 1995).

IMPACT ASSESSMENT
This analysis is followed by an assessment of the impact. This process of the LCA aims at the evaluation of the importance of the impacts that are prominent on the environment. These assessments were measured on the impacts based on the following element:
AND ITS VARIANTS

Life cycle analysis is valid only and only if the data within it is correct, hence the most important part of the analysis is data itself and it is crucial for data should be complete in the life cycle with a perfect and latest updates. Then the analysis of life cycle are compared with each other, it again becomes important that the data available is for both the available products as well as the process. Even when one of the data of one product is slightly higher then definitely there is no way that it can be compared to another having lesser detailing of data.

Validity of Data is another important issue in analyzing the life cycle of data. As globalization and the speed of development and technology yielding research and finding of new material and manufacturing is increasing and being introduced

HOT SPOT ANALYSIS
This particular section is all about a complete analysis of the complete life cycle of the Canon Printer, inclusive of all separate and discrete stages of the product. The impact of each stage has to be analysed and then only we get a complete detailing of all the information. The results from the Total Performance Indicator are used separately for every stage and plotted in a graph provided with an observation each.


OBSERVATION
This graph signifies that the usage of which product in the manufacture is the highest which is also obvious from the table used before that it is PS and then cardboard and thus, is there consumption. The consumption of these two has to be reduced and thus, methods in regard to their reduction are to be sorteduce the impact as well NSITIVITY ANALYSIS

The printer bulk and the material used and consumed are both with the codes of Boustead although there were also certain elements that were not of this code of database. In such cases, the use of a substitute was entertained or in some cases instead some element of that basic component was removed. The sensitivity analysis of these products as well as the omission of these elements was noted Dick (1994).

CONCLUSION

At the end of the report, it can be visualized and declared effectively that the LCA is helpful in improving the selected product of ours that is the Canon printer and hence reduce the threat to the environment.

The assessment remains incomplete if the conclusions regarding the product are not studied well and not finalized

Less use of the printer in a way that not heavy paper be usd in the printer. The printer should be optimized such that energy be saved. In offices, the printers are an important part but as yet they are not used throughout the day at all times of the day. Hence, in those times the printer should be put to standby mode. The number of hours the printer is used should be regulated in a way that the work load of the printer should be reduced and instructions should be given to the office staff about shifting to the standby mode (Alexandris 2006).

References
Alexandris, K., Kouthouris, C., Meligdis, A., (2006), “Increasing customers' loyalty in a skiing resort: The contribution of place attachment and service quality”,

Hi Dear

This is to inform you that we are one of the top educational company helping students in getting good grades in their academic life. We understand that you are interested in getting help in your Academic Assignments at affordable rates to get great results. All our tutors have Master's and PhD degree in different subjects and they are professors in most popular Universities of USA, UK, Australia and Canada. Sample Assignment provide assignment help, homework help, online exam help and online coursework help in different subjects and their sub-divisions like Accounting, Finance, Management, Engineering, Statistics, Economics and many more subjects. The way to use our services is very simple. You just need to mail your questions at info@sampleassignment.com and we will get back to you with a customized and affordable price quote for each and every assignment. Thanks and Regards, Sample Assignment Team info@sampleassignment.com -- Sample Assignment Team www.sampleassignment.com.

Media Contact
www.sampleassignment.com
***@sampleassignment.com
+61 401 358 795
End
Source:www.sampleassignment.com
Email:***@sampleassignment.com Email Verified
Tags:Assignment Help Australia, Assignment Help Uk, Online Assignment Help, Homework Help, Assignment Help
Industry:Education
Location:Melbourne - Victoria - Australia
Account Email Address Verified     Account Phone Number Verified     Disclaimer     Report Abuse
Sample Assignment PRs
Trending News
Most Viewed
Top Daily News



Like PRLog?
9K2K1K
Click to Share